The following diagram is the basic design diagram of inverter circuit. The circuit will convert 12V DC to 120V AC. This basic inverter circuit can handle up to 1000Watts supply depends the T1, T2 and transformer used. Please see the note.
Part | Total Qty. | Description | Substitutions |
C1, C2 | 2 | 68 uf, 25 V Tantalum Capacitor | |
R1, R2 | 2 | 10 Ohm, 5 Watt Resistor | |
R3, R4 | 2 | 180 Ohm, 1 Watt Resistor | |
D1, D2 | 2 | HEP 154 Silicon Diode | |
Q1, Q2 | 2 | 2N3055 NPN Transistor (see “Notes”) | |
T1 | 1 | 24V, Center Tapped Transformer (see “Notes”) | |
MISC | 1 | Wire, Case, Receptical (For Output) |
1. Q1 and Q2, as well as T1, determine how much wattage the inverter can supply. With Q1,Q2=2N3055 and T1= 15 A, the inverter can supply about 300 watts. Larger transformers and more powerful transistors can be substituted for T1, Q1 and Q2 for more power.
2. The easiest and least expensive way to get a large T1 is to re-wind an old microwave transformer. These transformers are rated at about 1KW and are perfect. Go to a local TV repair shop and dig through the dumpster until you get the largest microwave you can find. The bigger the microwave the bigger transformer. Remove the transformer, being careful not to touch the large high voltage capacitor that might still be charged. If you want, you can test the transformer, but they are usually still good. Now, remove the old 2000 V secondary, being careful not to damage the primary. Leave the primary in tact. Now, wind on 12 turns of wire, twist a loop (center tap), and wind on 12 more turns. The guage of the wire will depend on how much current you plan to have the transformer supply. Enamel covered magnet wire works great for this. Now secure the windings with tape. Thats all there is to it. Remember to use high current transistors for Q1 and Q2. The 2N3055’s in the parts list can only handle 15 amps each.
3. Remember, when operating at high wattages, this circuit draws huge amounts of current. Don’t let your battery go dead :-).
4. Since this basic inverter project produces 120 VAC, you must include a fuse and build the project in a case.
5. You must use tantalum capacitors for C1 and C2. Regular electrolytics will overheat and explode. And yes, 68uF is the correct value. There are no substitutions.
6. This circuit can be tricky to get going. Differences in transformers, transistors, parts substitutions or anything else not on this page may cause it to not function.
Do you have a bicycle..? why don't try to build this circuit..?. Powered using battery…
This is the circuit diagram of 3A switching power supply regulator: Simple and cheap, the…
Here is the remote control tester circuit. This circuit is really a simple and easy…
This is the circuit diagram of current output multiplier designed for regulator IC LM78xx. By…
The following diagram is the FM tracking transmitter based on 4 transistors. No additional notes…
This is the circuit diagram of white line follower toy. The actuator of the toy…
View Comments
i want to know if upgrading the device will permit the change of the 25V/68uF? if you are on line right now then please reply me quick. am waiting
68uF (C1 and C2) together with (R3 and R4) is to determine the frequency. It should be valid value. Tantalum capacitor (and metal film resistor) is a must to get the right wave frequency.
i really appreciate people like you at least for bringing out your time to to post these circuit
and their diagrams. could you please send me a 12v dc 240ac inverter circuit diagram ?,
Regard
Hey there can any one help me out....i want to make a 4.5v DC to 4.5v AC inverter circuit....can any one help me with the circuit diagram...
Dear Sir
I have tested my project, but it is giving same output as per input, and my transsfer is getting heatedup. I tried with it 6 volt charing battery.
Pl. inform to me to make corrective action in this regard.
Thank you
"Hi all,I have intex UPS for my desktop for 20mins backup. I want to increase the backup time to 1-2hrs. So one of my friend suggested me to use additional same battery as external Ups which can be connected with my current intex UPS whether it can be connected thru series or parallel? If i do like this will i face any problems? If yes what sort of problems? If i get answers for my above question i'll be feel happy... Please help.."
Of course if you want to add a battery, it must be connected paralel. Series connection will doubled the voltage while paralel connection will doubled the electric current.
please can you detail me on solar circuit diagram and inverter circuit diagram
sir plz send me full supll my home inverter diagram componet transformer autocut ups plz full detail me.thank u
i want home applicetion 12volts dc to 230volts ac circuit sir plese send me sir
Sir I have an UPS which is not working good it's giving out 330vac. Can you please send me the 12vdc to 240vac 400w inverter circuit diagram so that I try to use this UPS transformer to it?
Thanks
can this company supply 5000kva inverters for some companies?