The following diagram is the basic design diagram of inverter circuit. The circuit will convert 12V DC to 120V AC. This basic inverter circuit can handle up to 1000Watts supply depends the T1, T2 and transformer used. Please see the note.
Part | Total Qty. | Description | Substitutions |
C1, C2 | 2 | 68 uf, 25 V Tantalum Capacitor | |
R1, R2 | 2 | 10 Ohm, 5 Watt Resistor | |
R3, R4 | 2 | 180 Ohm, 1 Watt Resistor | |
D1, D2 | 2 | HEP 154 Silicon Diode | |
Q1, Q2 | 2 | 2N3055 NPN Transistor (see “Notes”) | |
T1 | 1 | 24V, Center Tapped Transformer (see “Notes”) | |
MISC | 1 | Wire, Case, Receptical (For Output) |
1. Q1 and Q2, as well as T1, determine how much wattage the inverter can supply. With Q1,Q2=2N3055 and T1= 15 A, the inverter can supply about 300 watts. Larger transformers and more powerful transistors can be substituted for T1, Q1 and Q2 for more power.
2. The easiest and least expensive way to get a large T1 is to re-wind an old microwave transformer. These transformers are rated at about 1KW and are perfect. Go to a local TV repair shop and dig through the dumpster until you get the largest microwave you can find. The bigger the microwave the bigger transformer. Remove the transformer, being careful not to touch the large high voltage capacitor that might still be charged. If you want, you can test the transformer, but they are usually still good. Now, remove the old 2000 V secondary, being careful not to damage the primary. Leave the primary in tact. Now, wind on 12 turns of wire, twist a loop (center tap), and wind on 12 more turns. The guage of the wire will depend on how much current you plan to have the transformer supply. Enamel covered magnet wire works great for this. Now secure the windings with tape. Thats all there is to it. Remember to use high current transistors for Q1 and Q2. The 2N3055’s in the parts list can only handle 15 amps each.
3. Remember, when operating at high wattages, this circuit draws huge amounts of current. Don’t let your battery go dead :-).
4. Since this basic inverter project produces 120 VAC, you must include a fuse and build the project in a case.
5. You must use tantalum capacitors for C1 and C2. Regular electrolytics will overheat and explode. And yes, 68uF is the correct value. There are no substitutions.
6. This circuit can be tricky to get going. Differences in transformers, transistors, parts substitutions or anything else not on this page may cause it to not function.
Do you have a bicycle..? why don't try to build this circuit..?. Powered using battery…
This is the circuit diagram of 3A switching power supply regulator: Simple and cheap, the…
Here is the remote control tester circuit. This circuit is really a simple and easy…
This is the circuit diagram of current output multiplier designed for regulator IC LM78xx. By…
The following diagram is the FM tracking transmitter based on 4 transistors. No additional notes…
This is the circuit diagram of white line follower toy. The actuator of the toy…
View Comments
Please I want to know if the diagram is for sine or square wave
this's the bacis of inverter circuit diagram. How can i design my circuit well?
Sir, i need a simple ups circuit and methods to produce it. like that of ups of a computer.
hi, am arnold(+23408133813260) from the ambrose alli university ekpoma, nigeria. thanks for the diagram, anyways, i would please kindly ask if you can also give a full diagram for a 1kva inverter which can take over once there is power failure, as i live in an area with an epiletic poweer supply...thanks and God bless.
Dearsir
I am a retired civil engineer and desire to keep muself busy in learning about making of solar panel dry battery which could finally help me in building 12v that is dry battery running on with the solar panel.Since I am not perfect in doing so.Kindly semd illustrative information in this regard along with necessary sketches and oblige.
I shall remain thankful
Pls sir i need the circuit diagram for inverter
Dear sir plaese send my e mail eddress complete ups basic easy diagrame urgently am wait your
reply very thanks.
I Need a 5 Kva Inverter Diagram with 48 volts DC input. If you have please send me on surajbhushan@gmail.com
Thanks In Advance.
Dear Sir,
I just want to make 12v dc to 240v ac,60Watt inverter with the same circuit instead of tantalum capacitors for C1 and C2 if I use 68 uf, 25 V Regular electrolytics capacitors beacause of low power. please sugest me
please send me a simple 12v to240 inverter circuit for my PC.I will be glad ,if iwill get different types