The following diagram is the basic design diagram of inverter circuit. The circuit will convert 12V DC to 120V AC. This basic inverter circuit can handle up to 1000Watts supply depends the T1, T2 and transformer used. Please see the note.

Basic Inverter Components list:

Part Total Qty. Description Substitutions
C1, C2 2 68 uf, 25 V Tantalum Capacitor
R1, R2 2 10 Ohm, 5 Watt Resistor
R3, R4 2 180 Ohm, 1 Watt Resistor
D1, D2 2 HEP 154 Silicon Diode
Q1, Q2 2 2N3055 NPN Transistor (see “Notes”)
T1 1 24V, Center Tapped Transformer (see “Notes”)
MISC 1 Wire, Case, Receptical (For Output)

 

Notes:

1. Q1 and Q2, as well as T1, determine how much wattage the inverter can supply. With Q1,Q2=2N3055 and T1= 15 A, the inverter can supply about 300 watts. Larger transformers and more powerful transistors can be substituted for T1, Q1 and Q2 for more power.

2. The easiest and least expensive way to get a large T1 is to re-wind an old microwave transformer. These transformers are rated at about 1KW and are perfect. Go to a local TV repair shop and dig through the dumpster until you get the largest microwave you can find. The bigger the microwave the bigger transformer. Remove the transformer, being careful not to touch the large high voltage capacitor that might still be charged. If you want, you can test the transformer, but they are usually still good. Now, remove the old 2000 V secondary, being careful not to damage the primary. Leave the primary in tact. Now, wind on 12 turns of wire, twist a loop (center tap), and wind on 12 more turns. The guage of the wire will depend on how much current you plan to have the transformer supply. Enamel covered magnet wire works great for this. Now secure the windings with tape. Thats all there is to it. Remember to use high current transistors for Q1 and Q2. The 2N3055’s in the parts list can only handle 15 amps each.

3. Remember, when operating at high wattages, this circuit draws huge amounts of current. Don’t let your battery go dead :-).

4. Since this basic inverter project produces 120 VAC, you must include a fuse and build the project in a case.

5. You must use tantalum capacitors for C1 and C2. Regular electrolytics will overheat and explode. And yes, 68uF is the correct value. There are no substitutions.

6. This circuit can be tricky to get going. Differences in transformers, transistors, parts substitutions or anything else not on this page may cause it to not function.

circuit schematic

View Comments

  • hi, am arnold(+23408133813260) from the ambrose alli university ekpoma, nigeria. thanks for the diagram, anyways, i would please kindly ask if you can also give a full diagram for a 1kva inverter which can take over once there is power failure, as i live in an area with an epiletic poweer supply...thanks and God bless.

  • Dearsir
    I am a retired civil engineer and desire to keep muself busy in learning about making of solar panel dry battery which could finally help me in building 12v that is dry battery running on with the solar panel.Since I am not perfect in doing so.Kindly semd illustrative information in this regard along with necessary sketches and oblige.
    I shall remain thankful

  • Dear sir plaese send my e mail eddress complete ups basic easy diagrame urgently am wait your
    reply very thanks.

  • Dear Sir,
    I just want to make 12v dc to 240v ac,60Watt inverter with the same circuit instead of tantalum capacitors for C1 and C2 if I use 68 uf, 25 V Regular electrolytics capacitors beacause of low power. please sugest me

  • please send me a simple 12v to240 inverter circuit for my PC.I will be glad ,if iwill get different types

1 6 7 8 9 10 12

Recent Posts

Switched ON Bike Lamp

Do you have a bicycle..? why don't try to build this circuit..?. Powered using battery…

55 years ago

3A Switching Power Supply Regulator

This is the circuit diagram of 3A switching power supply regulator: Simple and cheap, the…

55 years ago

Remote Control Tester

Here is the remote control tester circuit. This circuit is really a simple and easy…

55 years ago

Current Output Multiplier for 78xx Regulator

This is the circuit diagram of current output multiplier designed for regulator IC LM78xx. By…

55 years ago

4 Transistor FM Tracking Transmitter

The following diagram is the FM tracking transmitter based on 4 transistors. No additional notes…

55 years ago

White Line Follower

This is the circuit diagram of white line follower toy. The actuator of the toy…

55 years ago